Велотренажер Magene T300 PLUS

Полностью новый, ни разу не был в использовании Magene T300 PLUS Direct Drive Intelligent Riding Table Summary (Simplified Official Version) Direct drive electromagnetic intelligent riding platform, support Bluetooth FTMS / ANT + FE-C, compatible with Weng Deer Racing, Zwift, Myking assistant, blackbird and other software / stopwatch I. Product parameters Maximum power: 2600 W Maximum slope simulated: 22% Power accuracy: ± 2% (MDFP multi-sensor fusion algorithm with temperature compensation) Moment of inertia: 3.26 kg · m2 Noise: ≤ 56 dB (1.5m, 25km / h) Machine weight: 18 kg Power supply: 100-240 V wide voltage, output DC12V 5A Frame open file compatibility: 130 / 135 mm quick removal;12 × 142 / 12 × 148mm barrel shaft Flywheel compatibility: Shimano / SRAM 8-11 speed; Shimano 12 speed; SRAM XDR 12 speed (XDR tower must be purchased separately) Dimensions: 48 x 75 x 50 cm spread; Fold 48 x 21 x 50 cm Wheel Diameter: 700 C Highway / 26-29 Inch Mountain II. Packaging List Main, power adapter, fast-distorting rod, 130 / 135 fast-distorsing converter, HG barrel shaft cap, 12 × 142, 12 × 148 barrel axis transmission pads, flywheel washers, belt adjustment wrench, front wheel block, paper instruction manual III. Installation steps Open the riding platform Placed on a flat, hard surface, unlocked the orange hand. The leg heard a "click" to immobilize. Fine-tune the foot cushions. Both sides of the foot mattress land at the same time. Lock the screws. ✅ It is recommended to pair a riding platform mattress to prevent sliding, reduce noise and protect the floor. Installation of flywheel (HG Taki factory preinstalled) The chain hangs the smallest flywheels, and the flywheels are loaded into the tower in succession. The 8 - 10 speed flywheels must be equipped with gaskets Jet Wheel Cover Locked (Jet Wheel Wrench) Change the XDR base: 5 mm hexagonal counterclockwise screw down the end cap, pull out the HG base, install the XDR base re-locking end cap Loading a car (two ways) ✅ Fast-dismantling frames (130 / 135) The bike becomes the smallest flywheel + a small disc, remove the rear wheel Attach the corresponding starter converter, pass the fast detach rod through, and turn the spring tip inward The chain is aimed at the smallest flywheel on the riding platform, put down the frame, lock it, and remove it quickly; Shake the frame to make sure it doesn't loose. ✅ Barrel axle rack (12 × 142 / 12 × 148) Remove the rear wheels and replace the barrel shaft cap + the corresponding gear switch The frame is positioned, the chain is inserted into the flywheel, the barrel shaft is locked according to the standard torque of the frame, and shake to confirm stability IV. Activate and connect the app Plug in the power supply to indicate that the light is lit; Turn the handle to wake up the device 2.Download [Myking assistant] APP (Android / Apple), Bluetooth open APP search "T300 PLUS," according to the prompt mobile number verification code activation Once activated, you can use all of the smart resistance, firmware upgrades, and calibration functions Training software: Stag Racing, Zwift, TrainerRoad, Blackbird, etc., direct search for FTMS / FE-C device connections Two modes: ERG fixed power mode: software locks target power, automatically adjusts resistance (preferred for intermittent classes) Slope simulation mode (Slope): following the route slope automatically changes resistance, simulate road riding V. Servo calibration (the most important!) Ensure the power is accurate) Spin = Spindown, eliminate the error caused by bearing and belt friction, the new machine must do Preheating: 100 W or so for 10 minutes at a constant speed, so that the table temperature is stable 2.Mackin Assistant → Equipment Page → Reverse Calibration Follow the tips: Quickly stamp to a specified speed → Stop stamping, don't kick, and wait for free deceleration to complete Normal eligibility time: 40-60 seconds < 40s: too tight belt; > 60s: belt is too loose, use your own wrench to adjust belt tension 500долларов